基于壳聚糖多孔碳的制备及电容性能研究

以壳聚糖为碳源和氮源,采用预碳化处理和KOH活化两步法制备了壳聚糖多孔碳材料,考察了活化剂KOH用量对电极材料形貌、结构以及电容性能的影响。结果表明:当KOH与预碳化壳聚糖质量比为0.6∶1时,制备的多孔碳材料KOH-CTS-0.6具有最优的电化学性能。KOH-CTS-0.6具有大比表面积(1 348 m~2·g~(-1)),含有丰富的N、O元素(2.9%N和7.4%O)。在电流密度为0.5 A·g~(-1)时,KOH-CTS-0.6的比电容为235.2 F·g~(-1),显示出优秀的倍率能力;在电流密度为10 A·g~(-1)的大电流时,其比电容依然高达178.6 F·g~(-1)。此外,该材料还具有良好的循环稳定性,500次循环后比电容保持率为94%。     

空气预热器实时监控系统堵塞可视化性能研究

针对电站锅炉回转式空气预热器运行时上下表面不可见的问题，本文提出了一种视频监控与故障分析系统，可直接监测转子表面情况。该系统通过视频监控获取图像，结合改进的Retinex算法对其进行处理，实现了以下2个功能:1）能分析积灰程度以判断转子堵塞 情况；2）与温度场融合实时显示转子表面热点分布以预防二次燃烧。该系统已应用于某600 MW机组，实现了在热态环境下对空气预热器转子积灰程度、热点分布、堵塞程度的估算与可视化，大大提高了空气预热器运行的可靠性。     

平面桁架构建的定日镜面形支撑结构优化及实验

针对反射面成型的复杂影响因素，提出平面桁架构建的定日镜面形支撑结构优化技术路线. 利用模拟仿真、数值计算和优化算法等方法，解析20 m²定日镜面形定义技术路线的4个组成环节：面形规格及宽高比、上弦杆的截面矩、平面桁架组间距的最优值、机加工中工艺控制要点的量化. 试制小型定日镜进行实验，分析光斑形状和能流密度分布特性，并与理想球面形光斑比较，两者的拟合优度大于0.98. 实验结果表明，当反射镜宽高比取1.2，上弦杆截面矩取40 000 mm⁴，桁架组间距取950 mm，上弦杆和斜杆的开孔公差小于0.9 mm时，反射面形的质量提升. 研究从原理和实践上证明了该优化技术路线的可行性.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Predicting visual similarity between colour palettes

This work is concerned with the prediction of visual colour difference between pairs of palettes. In this study, the palettes contained five colours arranged in a horizontal row. A total of 95 pairs of palettes were rated for visual difference by 20 participants. The colour difference between the palettes was predicted using two algorithms, each based on one of six colour-difference formulae. The best performance (r² = 0.86 and STRESS = 16.9) was obtained using the minimum colour-difference algorithm (MICDM) using the CIEDE2000 equation with a lightness weighing of 2. There was some evidence that the order (or arrangement) of the colours in the palettes was a factor affecting the visual colour differences although the MICDM algorithm does not take order into account. Application of this algorithm is intended for digital design workflows where colour palettes are generated automatically using machine learning and for comparing palettes obtained from psychophysical studies to explore, for example, the effect of culture, age, or gender on colour associations.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

强织构铝合金残余应力检测技术研究

在铝合金轧板的残余应力研究中，由于其强烈的轧制织构，无法使用常规的X射线sin2 ψ法进行残余应力分析。以2A97铝锂合金轧制板材为研究对象，使用X射线衍射法测量材料的取向分布函数，结合Ruess、Voigt、Neerfeld-Hill模型，从理论上计算不同假设条件下材料的宏观弹性常数，得到材料表面的宏观残余应力。实验结合盲孔法进行对比验证，结果表明Neerfeld-Hill模型的残余应力分析结果与盲孔法所测结果相互吻合，建立织构材料的宏观残余应力分析方法。     

Cover Image

The cover image is based on the Research Article Observer‐Based Cooperative Distributed Fault‐tolerant Model Predictive Control with Imperfect Network Communication and Asynchronous Measurements by Guannan Xiao and Fei Liu, https://doi.org/10.1002/rnc.4994 .

     

大冶铜绿山矿区周边土壤—水稻中镉赋存状态及转化迁移规律研究

通过对大冶铜绿山矿区周边农田土壤、水稻系统采样分析表明,农田土壤中全量Cd的浓度范围为0.42～1.63 mg/kg,平均值为0.88 mg/kg,土壤中全量Cd含量与易利用态和中等结合态含量有较高的相关系数,相关系数0.8。在水稻籽实(大米)镉积累预测方面,选取土壤中全量Cd、pH、CEC、有机质建立的数学模型能较好地预测大米中Cd的累积。     

Anchoring single Pt atoms on hollow Ag3VO4 spheres for improved activity towards photocatalytic H2 evolution reaction

The high cost of noble metal catalysts has been a great bottleneck for the catalyst industry. Using the noble metal at a single-atom level for catalytic applications could dramatically decrease the cost. The impacts of single Pt atoms on the photocatalytic performance of Ag₃VO₄ have been investigated and reported. In this report, single Pt atoms were anchored on the surface of Ag₃VO₄ (AVO) as a cocatalyst, and the resultant composite photocatalyst has been studied for photocatalytic H₂ production from water driven by visible light. The as-prepared AVO particles are hollow nanospheres in the monoclinic phase with a bandgap of 2.20 eV. The light absorption edge of AVO/Pt is slightly red-shifted compared to that of the pristine AVO, indicating more visible light absorption of AVO/Pt. The XPS peaks of Ag, V, and Pt exhibit a significant shift after AVO and Pt get into contact, suggesting the strong interaction between the surface Ag and V atoms, and single Pt atoms. After 3-h illumination, the photocatalytic H₂ evolution amount from AVO/Pt is improved up to 1400 μmol, which is 2.8 times that on the bare AVO. Such efficient photocatalytic H₂ evolution on AVO/Pt is still maintained after five reaction cycles. The better photocatalytic performance of AVO/Pt has been attributed to the more efficient visible light utilization and the lower interfacial charge transfer resistance, as demonstrated in the DRS and EIS spectra. The presence of the surface Pt atoms also leads to a higher amount of reactive radicals, which could efficiently promote the surface redox reactions.